2714 Die Block Steel

About 2714 Die Block Steel

2714 Die Block Steel Chemical composition - (Typical analysis in %) Standards DB6 DIN2714 AISI L6 AFNOR 55NCDVV7 JIS SKT4 55iNiCrMoV C Si Mn P S Cr Ni Mo V 0.50-0.60 0.10-0.40 0.65-0.95 <0.015 <0.004 1.00-1.20 1.50-1.80 0.45-0.55 0.07-0.12 USA Europe Germany China Japan India R.of Korea Russia AISI/SAE En DIN,WNr GB JIS IS KS GOST A681 L6 55NiCrMoV7 56NiCrMoV7 5CrNiMo SKT 4 T55Ni7Cr4Mo5V1 STF 4 4ChMNFS Ventura Alloy and Steels Stocks and Supplies 2714 Die Block Steel in India and abroad. DB6 Steel is an extreme pass on steel with high treating resistance and great through-solidifying properties. Its nickel substance has it uncommonly effect safe - a highly recommendable element for vast mallet & press bites the dust alike. This evaluation is generally supplied in toughened condition or extinguished and tempered to 1300 N/mm & a working hardness of 370 to 410 HB (round) or 355 to 400 HB (square, level).Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.Utilized as standard steel for manufacturing passes on of different kinds, press bites the dust, expulsion kicks the bucket, retainer plates, heavily clad trim bites the dust, hot shear sharpened pieces of steels and instrument holder.PROCESS ROUTEEAF+LF+VD+UPSET+FORGED+ANNEALED+ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS+OIL QUENCHED AND DOUBLE TEMPERED+ ROUGH TURNED FOR ROUNDS/MILLED FOR FLATS STEEL PROPERTIESThe special Hot Work Pre-hardened Steel has great toughness and high wear resistance. DB6 Steel is generally supplied in hard, quenched, tempered and also in annealed condition in special cases.Usually its working hardness is 360-430 BHN. This steel grade is the upgraded version of DIN 2713 for greater efficiency and performance.APPLICATIONDies for Specially Drop and Close Die Forgings for Hammers & Mechanical Presses, Die Moulds,Shoe Blocks, Die Holder, Cassettes, Piston Rods, Cranks, Boaster, Shearing Blades, Tools, plastic moulds Etc.PHYSICAL PROPERTIES Coefficient of Thermal Expansion atC 10 m/(m*K) 20-100 12.1 20-200 13.1 20-300 13.2 20-400 13.5 20-500 14..1 20-600 14.3 Thermal Conductivity at C W/(m/*K) 20 35.0 350 39.0 700 36.0 HEAT TREATMENT Soft annealing C 650-710 Cooling Furnace Hardness HB max, 240 Hardening C 840-880 /860-900 Quenching Oil / Air Hardness after quenching HRC 57 / 55 Tempering C after quenching 100 200 300 400 450 500 550 600 600 in Oil -HRC 56 54 52 49 47 46 43 38 34 in Oil -HRC 54 52 50 47 45 43 40 36 32 Size Range: Rounds - 60 To 1000 Mm Dia.Blocks - Thickness - 125 To 1000 Mm Max | Width - 130 To 1600 Mm Max.